Author: Site Editor Publish Time: 2026-11-19 Origin: Site
304, SUS304 and 1.4301 are common, synonymous designations for stainless steel. However, when it comes to CNC-machined parts, the correspondence of grade designations is merely the starting point. Before a proposed equivalent material is accepted, the relevant material standards, the form and condition of the raw material, and the documentation provided for the respective batch should be compared.
Suppliers may offer materials held in local stock based on foreign drawings. The crucial factor here is whether these stock items meet the requirements for the parts as set out in writing and whether they have been approved by the persons responsible for material selection. This guide explains the points that engineers or purchasers should check before authorising machining.
Key Takeaways
Use a grade cross-reference to identify a candidate, then check the actual material specification and certificate.
Separate the alloy designation from the product standard, stock form and supply condition.
Keep 304L and dual-certified material distinct from a general claim of 304 equivalence.
Resolve any substitution before stock is purchased or cut, and make the accepted material identifiable in the order.
Although these designations refer the purchaser to the same broad category of austenitic stainless steel, they originate from different nomenclature systems. It is not possible to define all procurement requirements unambiguously on the basis of these designations alone.
Outokumpu's austenitic grade overview identifies 304 with EN 1.4301. Daido Steel's JIS comparison table places SUS304 alongside 304 in its similar-grade columns. That historic manufacturer table is useful for orientation; it is not a substitute for the applicable standard and order requirements.
Label on a drawing or offer | What it helps identify | What still needs checking |
|---|---|---|
304 | A commonly used stainless steel type designation | Governing product specification, condition and batch evidence |
SUS304 | The JIS grade designation | Applicable JIS product standard and whether the proposed stock meets it |
1.4301 | The EN steel number commonly associated with 304 | Applicable EN product standard, stock form and specified properties |
S30400 | The UNS alloy designation associated with 304 | The specification under which the material was supplied and tested |
The S30400 correspondence is also listed in thyssenkrupp Materials UK's 304/1.4301 datasheet. The table above is a navigation aid, not an unconditional interchangeability statement. A buyer serving a US, European, Japanese or Korean project should preserve the customer's actual specification rather than infer it from the shipping destination.
Grade designations and product standards each address different issues. Grade designations are used to identify alloys; product standards, on the other hand, relate to specific categories of material products and the requirements for them. Please include both pieces of information in your enquiry.
For example, the public scope of ASTM A276/A276M concerns stainless steel bars and shapes. The public scope of ASTM A240/A240M concerns stainless steel plate, sheet and strip. These references illustrate why a plate datasheet does not automatically establish the requirements for round bar.
In the case of machined housings, the supplier should be asked which raw material is to be used. Although parts cut from sheet metal and those machined from bar stock may bear the same grade designation, the procurement documents must nevertheless be checked to ensure they meet the correct product requirements. If the product shape or standard is specified in the drawings, a clear decision must be made regarding any change to the raw material used.
Before comparing chemistry or strength, put these details side by side:
The standard designation and the edition required by the drawing, contract or purchase specification.
The exact grade, including suffixes such as L where specified.
The proposed stock form, size and delivery condition.
Any additional customer requirements for testing, documentation or origin.
If the drawing says only "304 stainless steel," ask the design owner to resolve the missing purchase requirements. Do not fill the gap by choosing whichever standard appears first in a supplier's brochure. The broader drawing and order package is covered in Dawang Precision's CNC machining RFQ checklist.
Review the material in the condition in which it will be supplied. The same grade name does not tell the buyer whether the stock is annealed or cold worked, or establish the mechanical properties of a particular delivery.
ASTM's public A276 abstract distinguishes supplied conditions and mechanical testing. Daido's stainless steel classification guide also explains that austenitic stainless steel can harden through cold working. These sources support checking condition instead of treating a grade label as a complete property statement.
Ask the supplier to specify the required criteria in the quotation and to submit the relevant material documentation by the agreed deadline. Compare the reported chemical and mechanical test results with the acceptance limits set out in the relevant specification. In doing so, keep an eye on the test lots, stock levels and the basis for testing.
Typical values are not acceptance limits. A manufacturer's published typical chemistry can explain a grade, but it does not prove that a particular heat meets your order. Where a requirement is missing from the certificate, request clarification or the agreed additional evidence. A blank field is not a pass.
This review should also address the part's intended use. If welding, corrosion exposure or another functional requirement drove the original selection, the responsible engineer should assess the proposed material against that requirement. A machining supplier's availability statement cannot settle a design question by itself.
Do not treat the designations ‘304’, ‘304L’ and ‘304/304L’ as interchangeable. They denote different properties, which must be verified on the basis of the order.
The thyssenkrupp data sheet distinguishes between 304/1.4301 and the low-carbon 304L/1.4307, and points out that some products are available with dual certification. This means that, for a specific product, it can be documented that it meets both criteria; however, it does not mean that every item sold as 304 is also 304L.
If a supplier offers dual-certified stock, ask which specifications and grades are actually specified in the documentation. Check whether the required conditions, tests and additional purchase requirements are included. Do not assume dual certification is present simply because of a listing on a website or a handwritten ‘304/304L’ label.
If the drawing explicitly specifies 304L, a quotation that only includes 304 must be clarified before purchase. Similarly, a proposal to use 304L instead of 304 in accordance with a drawing should be assessed against all applicable requirements, rather than being accepted simply because the designation sounds more specific. The designer decides whether the proposed material is suitable; this decision should be recorded in the procurement documentation.
An accepted substitution should remain identifiable from the supplier's offer through the finished-part delivery. Request documentation and traceability appropriate to the order, and confirm what the supplier can provide before placing it.
Use this checklist as an engineering and purchasing aid. It is not a certificate template or a claim that every project needs the same inspection document.
Check | Evidence to request or agree | Question to close before machining |
|---|---|---|
Required material | Drawing note, material specification and purchase requirements | What exactly must the material meet? |
Proposed stock | Exact grade, product standard, form, size and condition | Is this the same requirement or a proposed substitution? |
Batch identity | Mill or material certificate with the relevant heat or lot reference | Can the proposed stock be linked to this document? |
Acceptance | Required limits, reported results and any agreed additional checks | Are there missing results or unresolved differences? |
Part-to-stock link | Agreed identification records through cutting and machining | Can delivered parts be linked back to the accepted material? |
Approval scope | Written acceptance identifying the part, order and material proposal | Does approval cover this supply only or future orders too? |
If the procurement specifications require the submission of certificates, the type of certificates required should be clearly defined. If the customer requires specific documents, vague wording such as ‘including material certificates’ should be avoided. Dimensional inspection reports merely describe the measurement data of the parts; they do not in themselves serve as proof of the origin of the raw materials.
For repeat orders, enquiries should be made as to whether the origin, specifications or condition of the material supplied have changed. A previous acceptance must not be regarded as blanket approval for different stock items. Even if the geometry of the parts has not changed, this still constitutes a material acceptance test.
Let us assume that this is the housing of a CNC machine tool, for which the material designation EN 1.4301 is specified in the drawings and which is subject to a specific procurement specification. The supplier delivers round bars made of SUS304. This is an illustrative procurement scenario; it is neither a customer case for Da Wang nor an approved material alternative.
Firstly, enquiries should be made regarding the product standards applicable to these round bars, the delivery condition and the associated documentation. This information must be cross-checked against the drawings and the procurement requirements. Cross-references merely indicate that engineers should assess the suitability of SUS 304; however, they do not constitute proof that this specific round bar meets all requirements.
If the material documentation clearly confirms the required specifications and the specified material designation, verify this evidence against the full purchase order. If the documentation merely confirms the proposed alternative, submit the discrepancies to the design engineer, who will then decide whether to proceed with the substitution. Under no circumstances should you label the material as EN-compliant simply because the chemical composition appears similar.
Record the outcome in plain language: the accepted stock specification and condition, the evidence reviewed, any remaining tests, and the orders or quantities covered. If the proposal is rejected, keep the original requirement in the sourcing request. This prevents a commercial quote comparison from quietly becoming a material change.
A useful material request states the required grade and product standard, proposed stock restrictions, condition, documentation and substitution rule. If you are open to alternatives, ask suppliers to list each alternative separately with the evidence needed for review. This keeps the original requirement visible while allowing availability discussions.
Dawang Precision's CNC milling service describes a drawing-led review of material and inspection needs before confirming a manufacturing plan. To discuss a stainless steel part, submit your drawing and material requirements for a quotation, including any proposed alternative that needs engineering acceptance. Confirm material availability and documentation for the specific project during that review.
Prepared by Dawang Precision. This article draws on public manufacturer references and standards catalogue scopes, checked on November 17, 2026. It provides a purchasing review method, not a certification of material equivalence. For project-specific questions, contact the Dawang Precision team.